There are many molding processes for carbon fiber composite materials, and the selection of molding processes mainly considers the structural characteristics of the components, existing molding equipment, and manufacturing costs. The structural characteristics of UAV composite components include five types: composite laminate structure, honeycomb sandwich structure, foam sandwich structure, aviation sandwich structure, and pipe fitting structure.
We have a relatively complete range of carbon fiber composite material forming and testing equipment, and strive to adopt low-cost methods in mold design, manufacturing, component forming technology, and assembly. The carbon fiber of the drone carbon fiber composite component is selected from Toray T300 long fiber and carbon fiber woven cloth, the matrix material is selected from a high-performance epoxy resin system cured at medium temperature, and the honeycomb material is Nomex honeycomb provided by our company. The foam sandwich material is low-density high-strength polyurethane foam, which is made by foaming the mixed liquid composed of the main materials of polyether and isocyanate.
Corresponding molding processes are adopted based on the different characteristics of composite body components of unmanned aerial vehicles. Below, we will introduce the manufacturing of the components separately.
Hot press molding process
The Ω - shaped beams inside the fuselage and the U-shaped beams on the wings are load-bearing members, using a carbon fiber composite laminated plate structure. In order to obtain a dense internal quality, the hot press molding process is adopted. Firstly, carbon fiber and epoxy resin need to be made into pre impregnated materials, followed by strict layering procedures.
1) Production of prepreg
Material: Reinforced carbon fiber Toray T300-3000-40B.
Medium temperature curing system of epoxy resin as the matrix material.
Equipment: Hot melt drum layout machine.
The carbon fiber arranging machine we use (as shown in the figure below) is a modification of the traditional solution method arranging machine, adding a resin heating device to enable the production of non-woven fabric prepreg using both solution and hot melt methods. Due to the fact that the high-performance epoxy resin used in the carbon fiber composite material for drones is solid at room temperature, the hot melt method is chosen. First, the epoxy resin is made into small pieces and heated to a molten state in a glue tank. After reaching the appropriate viscosity, the equipment is turned on to immerse a single bundle of carbon fibers in the molten epoxy resin, which is then wrapped around a large-diameter drum to form a non-woven fabric.

The non-woven fabric prepared by melting method does not contain solvents, which can effectively reduce the porosity of laminated boards and improve product quality. The carbon fibers in the non-woven fabric are parallel to each other, and the laying angle of the fibers can be precisely controlled during layering. The fiber is straight without buckling, which increases the mechanical properties of the fiber.
The most critical quality indicator for preparing prepreg by melting method is to control the gel content of the prepreg. The adhesive content R of the prepreg depends on the adhesive content R of the product. The amount of adhesive flow X during the solidification of the product in the hot press tank. There is a quantitative relationship between the adhesive content of prepreg, product adhesive content, and flow adhesive content as follows:
The tensile performance test results of R=1- (1-X) (1-R) (8-1) composite material show that the optimal mechanical properties of the composite material are achieved when the adhesive content of the non-woven fabric and the composite material are controlled at (40 ± 2)% and (32 ± 2)%, respectively.
2) Forming process flow
(1) Mold preparation.
The hot press can molding mold requires the mold material to maintain dimensional stability under high temperature and high pressure during product molding, taking into account factors such as mold cost, machinability, and thermal conductivity. Forming drone composite beam: Aluminum alloy mold is selected for the wall mold. The mold is a concave mold, and the mold surface is polished smooth and polished. Stick a PTFE release cloth with adhesive on the surface of the mold, which has a good release effect. When the contact surface is bonded to the body skin, there is no need to clean the release agent.
(2) Pre impregnated material cutting and stacking.
Lay non-woven fabric flat on the desktop of the automatic fabric cutting machine (as shown in the figure below), and control the actual direction of fiber cutting, generally not exceeding ± 1 with the design requirements. When using an automatic fabric cutting machine for cutting, it is necessary to prevent the fabric layer from moving to avoid angle deviation.
When laying the fabric layer on the mold surface, it should be manually laid in strict accordance with the designed laying sequence and direction, and the prepreg should be flattened and compacted as much as possible to eliminate interlayer air.

(3) Production of vacuum bag system. The auxiliary materials required for the production of vacuum bag systems include vacuum bag film, sealing putty strip, perforated isolation film, adhesive absorbing material, breathable felt, and PTFE release cloth. Combine the blank and auxiliary materials into a vacuum system as shown in the following figure. The amount of adhesive layer used should be accurately calculated. After bagging, the system should perform vacuum leak detection. After stopping the pumping, maintain the pressure for more than 10 minutes. If the vacuum degree does not decrease, close the hot press tank door.

(4) Component molding and processing.
Set the temperature time and pressure time curves according to the curing process parameters of epoxy resin, and run the program to heat up and cure. This model of drone adopts a medium temperature curing system, which has the advantages of low molding temperature, short molding cycle, low internal stress of the parts, good dimensional stability, high fracture toughness, and can significantly reduce energy consumption and production costs, and improve production efficiency.
After the solidification of the components is completed, the temperature inside the hot press tank (as shown in the figure below) can only be released when it drops below 50 ℃. The components are cooled to room temperature with the mold before demolding to prevent deformation caused by residual stress inside the components. The components are cut and processed according to the edge lines.
(5) Quality inspection.
To ensure the internal quality of the molded parts of the hot press tank, non-destructive testing is carried out using an ultrasonic C-scanner. Ultrasonic C-scan can detect defects such as porosity, interlayer, delamination, porosity, thickness, fiber content, fiber orientation, etc. inside composite materials. When conducting C-scan testing on composite materials, the ultrasonic transducer and specimen are placed in a water tank, with water as the coupling medium. The echo returns through a gate circuit to ensure that only the echo from the composite material can pass through. An amplitude threshold can be selected, and if the echo amplitude is above the threshold, it is judged as an unqualified area; Below the value, it can be determined as a qualified area. The transducer is connected to a mechanical device and can move over the entire specimen. C-scan images can provide a limited plane view of a specific depth beneath the surface of the specimen.
The following figure shows the ultrasonic CT scanning display system. When performing CT scanning operations, the ultrasound detection device is equipped with an electronic gating circuit that samples the received echoes at a selected cycle. It starts working at a selected activity time after the initial emission pulse. The selected activity time is proportional to the distance between the top of the detection limit and the depth of the test piece, and the length of time the gating circuit is disconnected is proportional to the thickness of the detection limit. When used with large aperture focusing transducers, CT scanning systems can produce detailed records with good discontinuous resolution. The obvious disadvantage of CT scanning is the generation of discontinuous two-dimensional plane views within a given depth range, so it is necessary to gradually increase the depth and repeatedly scan, otherwise it is difficult to provide information at another depth.

In laminated board testing, adjusting the discriminator level to the middle position between the minimum and maximum signal amplitudes can detect fiber orientation errors using ultrasonic C-scan method. When detecting delamination, adhesive defects, pores, and impurities, defects can be displayed in grayscale color patterns. Under certain conditions, the thickness deviation of fibers can be detected, but factors such as the flatness and evenness of the specimen surface, impedance matching of the transducer, incident angle, and coupling condition can all affect the detection results.
